Precision Optics Mounting and Zeroing in San Antonio

Your firearm is only as accurate as the optic mounted on it — and that optic is only as reliable as the gunsmith who installed it. RTF3TX Gunsmithing Live Oak, located in Live Oak near San Antonio, offers professional optic mounting, torque-specification installation, leveling, and bore-sighting performed exclusively by Master Gunsmith Roland Lamothe. As the sole AGI-certified service center in the San Antonio area, RTF3TX brings the discipline of a ten-year US Army veteran to every optics job that comes through the door. From mounting a red dot on a factory optic-ready pistol slide to zeroing a precision rifle scope, every task is executed with craft-level attention to detail. Proper pistol optic installation is a technical process — one that requires correct torque values, thread-locking compound at every fastener, and precise leveling before the firearm ever reaches the range. Shooters across Bexar County and throughout South Texas count on agicertifiedgunsmith.com/service-page/optics-sighting-services for sighting services that go well beyond basic assembly work. Roland's master-level training under AGI instructors Bob Dunlap, Gene Kelly, and Gene Shuey underpins every installation, ensuring that each optic is fitted with the same precision applied to custom hand-fitting and advanced firearm tuning. Pistol and rifle owners in the Live Oak and greater San Antonio region now have access to a dedicated facility that approaches optics work as the exacting craft it genuinely is.

📞 Call Now: +1 (210) 740-1811
Precision Optics Mounting and Zeroing in San Antonio

Master Gunsmith Optics and Sighting Services at RTF3TX Gunsmithing

What Correct Red Dot Installation Actually Involves

What Correct Red Dot Installation Actually Involves

Dropping a red dot onto a pistol slide and tightening the screws by feel is not installation — it is a recipe for a lost zero and a potential malfunction at the worst moment. Proper mounting begins with a thorough inspection of the mounting surface, continues with precise leveling of the optic body, and concludes with each fastener torqued to the manufacturer's specified value using a calibrated driver. Roland applies thread-locking compound at every fastener point to prevent the optic from walking under sustained recoil. For pistol owners in the greater San Antonio region looking for red dot sight installation San Antonio on a factory optic-ready or aftermarket pre-cut slide, RTF3TX Gunsmithing provides an installation standard that holds up over thousands of rounds. Suppressor-height co-witness iron sights are also fitted and properly adjusted as part of a comprehensive service package.
Rifle Scope Mounting, Ring Lapping, and Live-Fire Zeroing

Rifle Scope Mounting, Ring Lapping, and Live-Fire Zeroing

Even a premium rifle scope cannot perform to its potential if it is mounted with uneven ring pressure, misaligned bases, or improperly sequenced screw torque. At RTF3TX Gunsmithing in Live Oak, rings and bases are lapped when surface contact demands it, mounting hardware is torqued in the correct progression to eliminate tube stress, and thread-locking compound is applied to every appropriate fastener. Following installation, bore-sighting places the reticle on target before any live ammunition is expended, and subsequent range confirmation locks in the final zero for the shooter's specific load and intended distance. Hunters and competitive shooters throughout South Texas rely on this level of scope mounting and zeroing because a foundation that is off by a fraction of a degree compounds into significant error at distance.
AGI Certification and Veteran Accountability Behind Every Optic

AGI Certification and Veteran Accountability Behind Every Optic

Before becoming a master gunsmith, Roland Lamothe served ten years in the US Army — including two major combat tours — where precision under pressure was not optional. After his service, he earned his Master Gunsmith certification from the American Gunsmithing Institute through direct training under Bob Dunlap, Gene Kelly, and Gene Shuey. RTF3TX Gunsmithing is the only AGI-certified service center operating in San Antonio, and it runs as a strict solo-operator facility — every optics and sighting service is completed personally by Roland, with no delegation to assistants or junior technicians. This personal accountability, reinforced by 75 consecutive five-star Google reviews and full BBB accreditation, is precisely why pistol optic customers throughout Live Oak and Bexar County continue to return and refer others.

Frequently Asked Questions

No. Slide milling is not performed at this facility. Roland recommends that customers source a factory optic-ready or aftermarket pre-cut slide, then bring it in for professional optic mounting, torquing, leveling, and bore-sighting.

Available services include optic mounting, torque and leveling, suppressor-height sight installation, bore-sighting, and factory optic-ready slide fitting and assembly. All work is performed personally by Master Gunsmith Roland Lamothe to manufacturer and professional specifications.

When screws are under-torqued, recoil forces allow the optic to shift incrementally, causing zero loss. Over-torquing risks cracking the optic body or stripping the mounting threads. Hitting the exact specified torque value, secured with thread-locking compound, keeps the sight anchored where it was set.

He begins with bore-sighting to establish a starting point before any live fire, then verifies and fine-tunes the final zero at the range. This two-step approach conserves ammunition and ensures the optic is dialed in for the shooter's specific load and target distance. Learn more at visit agicertifiedgunsmith.com.

Yes. As the only AGI-certified gunsmith serving San Antonio and Live Oak, Roland provides red dot sight installation San Antonio shooters can count on, backed by 75 consecutive five-star reviews and full BBB accreditation.

Ready to Get Started?

We'd love to hear from you